Firmware download

Ver.2.03

A color mode Teal and Orange has been added.

Your device does not support this download service.

Update Procedure

How to check the current firmware version

Check 01

Turn on the camera.

Check 02

Press the MENU button on the back of the camera to display the Camera Set-up Menu.

Check 03

Select “Information” from the Set-up Menu.
Press the OK button again to display the firmware update window.
The installed firmware information is displayed.
If the version is “Ver.2.02” or lower, it is necessary to update to this new firmware version.

How to update the firmware

STEP 01

Please use 512MB or larger SD/SDHC/SDXC card and format the card in the camera body.
* To avoid loss of your important data, please check the SD/SDHC/SDXC card before formatting

STEP 02

For Windows
(It appears differently depending on OS version.)

For Macintosh
(It appears differently depending on OS version.)

Please connect a card reader containing the SD/SDHC/SDXC card or the dp2 Quattro to your computer and click the Download button or right click on the mouse (if you use a Macintosh computer, please press Control + click) to store the firmware file in the SD/SDHC/SDXC card root directory (Please do not store the file in a subfolder such as “DCIM”).

* If the firmware has downloaded whilst the camera is connected to your computer, please turn off your camera before disconnecting it from your computer.

STEP 03

Insert the SD/SDHC/SDXC card storing the firmware file of DP2QV203.BIN into your camera and turn on the dp2 Quattro.
* It is not necessary to connect the camera body to your computer.

STEP 04

Press the MENU button on the back of the camera to display the Camera Set-up Menu.

STEP 05

Select “Firmware Update” from the Set-up Menu.
Press the OK button again to display the firmware update window.
The installed firmware information is displayed.

STEP 06

“Start Firmware update?” message will be displayed.

In case of "Start Firmware Update" message is not displayed

In the unlikely event that the “Start Firmware update” message does not appear, an error message will be displayed in the lower part of display.
A list of possible reasons for this error message, along with the solutions, appear below.

No Firmware update file on Memory card

It is possible that the Firmware update file is not stored in the root directory. Please repeat the above installation from STEP : 02.

Cannot update firmware. No Memory Card.

Please turn off your camera and insert the SD/SDHC/SDXC card with the stored firmware “DP2QV202.BIN” (copied to root directory) into your camera. Then repeat the above installation from STEP : 03.

Cannot update firmware. Battery Empty.

Please use a dedicated fully charged battery and repeat the above installation from STEP : 03.

Cannot update firmware. Connecting cable.

USB cable from your camera. Please repeat above installation from STEP 03.

Cannot update firmware. Setting external flash.

Turn off the camera and remove the external flashgun from your camera. Please repeat the above installation from

STEP 07

Select “Yes” and then press the OK button to start the firmware update. Firmware update will now start.
(There will be two firmware updates. 5 seconds after starting the first update, the camera body will turn off automatically, and 3 seconds later it will turn on again to start the second update. In case the camera does not restart, turn on the power to resume the update. It takes about 1 minute as a total to update.)

Error!

If the “Firmware update has failed.” message appears during firmware updating, please check the Error Code, and contact your nearest Service Center. Please visit the following “World Network” page for contact details.

STEP 08

When the message “Firmware update is complete. The camera will be turned off automatically.” is displayed, the update is complete.
* Please do not operate the camera until the message “Firmware update is complete.” appears.

STEP 09

Select the “Information” from the Set-Up menu and confirm the firmware has been updated to “2.03”. If “2.03” is displayed, the update is complete.

Update History

Ver.2.02

It has corrected the phenomenon that there was some noise in the right side of the images, when DNG files were processed using Adobe Photoshop by Adobe Systems Incorporated.

* SIGMA Photo Pro ver. 6.5.4 or later is required to process the RAW data (X3F and X3I files) taken by the dp Quattro with firmware version 2.00 or later

Ver.2.01

It has corrected the phenomenon that buttons on the back of the camera do not work when restarting the camera after the update, depending on the camera settings.

* The latest version of SIGMA Photo Pro 6.5.4 is required to process the RAW data (X3F and X3I files) taken by the dp Quattro series after the firmware update.